Home > Switch Life Tester >

IEC 61386-22 Figure 101 Rigid And Corrugated Casing Bending Test Apparatus For Conduits Test

Product Categories

Electrical Appliance Testing Equipment [376]
Energy Efficiency Lab [43]
Vehicle Testing Equipment [136]
Battery Testing Equipment [67]
Switch Life Tester [271]
Led Testing Equipment [71]
Water Ingress Testing Equipment [83]
Environmental Test Chamber [106]
Flammability Test Chamber [60]
EMC Test Equipment [24]
Medical Device Testing Equipment [34]
IEC 62368 Test Equipment [73]
Test Equipment For Electric Lab [22]

Sinuo Testing Equipment Co. , Limited

Trust Seal

Verified Supplier

Credit Check

Supplier Assessment

Contact Now

IEC 61386-22 Figure 101 Rigid And Corrugated Casing Bending Test Apparatus For Conduits Test

Name: IEC 6138622 Figure 101 Rigid And Corrugated Casing Bending Test Apparatus For Conduits Test
Brand: Sinuo
Price: 1 USD

Buy cheap IEC 61386-22 Figure 101 Rigid And Corrugated Casing Bending Test Apparatus For Conduits Test product

Brand Name : Sinuo

Model Number : SN2905

Certification : Calibration Certificate (Cost Additional)

Place of Origin : China

MOQ : 1

Price : Customized

Payment Terms : T/T

Supply Ability : 20 Sets Per Month

Delivery Time : 30 days

Packaging Details : Plywood Case

Applied Standard : IEC 61386-22

Applied Clause : Clause 10.4

Sample nomisteelnal diameter : 6/8/10/12/16/20/25

Semi-rigid casing radius : 40/50/60/80/96/120/150

Bellows radius : 20/25/30/40/48/60/75

Material : Support frame made of steel

Contact Now

IEC 61386-22 Figure 101 Rigid And Corrugated Casing Bending Test Apparatus For Conduits Test

Product information:

This testing machine is suitable for bending tests on non-metallic conduits and other materials. First, according to IEC61386-22 Section 10.4.103 and Figure 101, bend to the left at an angle of 90°±5°, and return to the vertical position. After 1 minute, bend to the right again at 90°±5°, and then return to the vertical position and stay for 1 minute, and repeat this process 3 times. The last time the sample stays for 5 minutes and then bent to a position of 45°±5° with the vertical line, use the IEC61386-22 Figure 102 gauge to verify whether it can pass through the bent conduit. After the test, observe whether the sample has cracks. Comply with the requirements of Clause 6.6.2.3 and Figure 10 of JG3050-1998 "Insulated Electrical Bushings and Accessories for Buildings", "GB 20041.21-2008 Conduit Systems for Cable Management Special Requirements for Rigid Conduit Systems", GB/T14823.2 "Conduits for Electrical Installation" Special requirements - Rigid insulating material flat conduit", ZBG33008 "Polyvinyl chloride plastic corrugated wire conduit" and IEC61386-22 Section 10.4 and Figure 101 and other requirements.

IEC 61386-22 Figure 101 Rigid And Corrugated Casing Bending Test Apparatus For Conduits Test

Technical parameters:

1. Apparatus specification selection table (unit: mm)

No.	Sample nominal diameter	Semi-rigid casing radius	Bellows radius	Remark
1	6	40	20	Standard
2	8	50	25	Standard
3	10	60	30	Standard
4	12	80	40	Standard
5	16	96	48	Standard
6	20	120	60	Standard
7	25	150	75	Standard
8	32	192	96	Optional
9	40	300	160	Optional
10	50	480	200	Optional
11	63	600	252	Optional
12	75	720	300	Optional

2.Material: Support frame made of steel, guide wheel made of 6061 industrial aluminum

IEC 61386-22 Figure 101 Rigid And Corrugated Casing Bending Test Apparatus For Conduits Test

Product Tags:

IEC 61386-22 Conduits Test Apparatus

Corrugated Casing Bending Test Apparatus

IEC 61386-22 Figure 101 Rigid And Corrugated Casing Bending Test Apparatus For Conduits Test Images

Inquiry Cart 0

Send your message to this supplier


*From:	Your email address is incorrect!
*To:	Sinuo Testing Equipment Co. , Limited
*Subject:	Subject is empty!
*Message:	For the best results, we recommend including the following details: -Self introduction -Required specifications -Inquire about price/MOQ Characters Remaining: (0/3000) Please enter 20 to 3000 characters to contact this supplier!